Lubbock Elite
Fence
(806) 555-0100

Fence company in Lubbock, Texas

Lubbock Elite Fence | Fence Company for Cedar Privacy, Wrought Iron, Steel Pipe & Chain Link Fence Installation, Repair and Staining

Cedar on galvanized steel posts, iron, pipe and chain link, set in concrete through the caliche and built to stand through the spring wind. Repairs and staining too.

Written quote within 24 hours

Tell us about your fence

The measure is free; the written quote follows within a day of it.

Fence installation in Lubbock is decided a foot under the grass. Dig down and you hit caliche, a pale crust that bends a hand auger, so our Lubbock fence crew runs a rock auger and pours concrete around every post. A wood post fails like a bad tooth: at the gumline, where nobody looks, until one March afternoon the whole run is lying across the alley. That is why the posts under our cedar are 2 3/8 inch galvanized steel at 8 foot centers. Above them go 6 foot cedar privacy pickets, board-on-board with a cap and trim, horizontal slats, wrought iron, welded pipe or chain link.

Measure on Monday, written quote by Tuesday. Most backyards go up in a day or two. After a windstorm, fences that are down jump the line, because an open yard with a dog in it can't wait a week. In our opinion new cedar should sit a few weeks before it gets stain, and the west and south faces need it most; the afternoon sun here greys an unstained fence in a single summer. The same Lubbock fence builders handle gates, pergolas and commercial lots.

  • Steel posts set in concrete on every wood fence
  • Written quote within 24 hours of the measure
  • Wind and storm repairs put first on the schedule
  • Most backyards finished in one to two days
  • Stain and sealer offered on every new cedar fence

Residential

Residential fence installation in Lubbock

Cedar privacy fence on steel posts

Walk any alley in town and you will count this fence a hundred times: 6 foot dog-ear or flat-top cedar pickets on 2 3/8 inch galvanized steel posts, concrete at the base, three 2x4 cedar rails and ring-shank or stainless fasteners. It is popular because it works. From the yard side you see the steel brackets; a 1x4 wood wrap or a dome cap hides them for a little more per post if that bothers you.

Board-on-board cedar with cap and trim

Cedar shrinks here. In air this dry a side-by-side fence can show daylight between the pickets by its second summer, and board-on-board stops that by overlapping each picket over the gap of the last. Add a 2x6 cap and a 1x4 trim and both faces look finished. On a corner lot or an alley side we think it earns the extra $10 to $15 a foot.

Horizontal cedar and modern slat fences

1x6 horizontal cedar with a quarter-inch gap, on steel posts at 6 foot centers instead of 8, because a long horizontal board sags in the middle long before a picket would. It is the fence you see going in beside the stucco and stone houses on the newer south-side streets, usually stained dark. Leftover slats make a good screen for the pool pump or the trash cans.

Wrought iron and ornamental steel fences

Square-tube steel pickets in welded panels, powder-coated black, flat-top or spear-top, 4 to 6 feet tall, tied into brick or rock columns with matching walk and drive gates. Ask for galvanized steel under the paint. Blowing sand sandblasts a cheap finish down to bare metal at the welds within a few years, and that is where the rust starts.

Welded pipe and ranch fence

2 3/8 and 2 7/8 inch pipe, new or drill-stem, with a welded top rail and pipe, cable or sucker-rod rails below. Painted or left bare, it holds horses and cattle and frames the front of acreage homes out past the loop, from Wolfforth to Shallowater and Idalou.

Chain link fence installation

Galvanized or black vinyl-coated chain link in 9 and 11 gauge, 4 to 6 feet tall, with a top rail, tension bands and a bottom tension wire so dogs cannot push under. Privacy slats and windscreen turn a plain run into a screen for backyards, dog runs and lots.

Vinyl fence installation

Virgin PVC privacy and picket fence with steel-reinforced posts and aluminum-stiffened rails for wind load, plus UV inhibitors for the strong sun. Vinyl never needs stain. We will also say plainly when an open, windward lot is better served by board-on-board cedar or iron.

Masonry, stucco and rock column fences

Brick, block and stone columns with cedar or iron panels between them, and stucco-faced block walls along the street. Footings go below the caliche so the columns stay plumb, and the caps shed water. It is the look of many of the older brick neighborhoods in town.

Pool fence installation

A barrier at least 48 inches tall, gates that close and latch on their own, and gaps under 4 inches, built in ornamental steel or aluminum so the pool stays in view. We set the latch height and the gate swing to code and confirm the current rule with the City before building.

Driveway gates, sliding and rolling gates

12 to 20 foot swing gates and cantilever slide gates on welded steel frames, faced in cedar or iron to match the fence. Drop rods, lockable latches and operator-ready posts come with every drive gate, so a keypad or opener can be added later without a rebuild.

Dog fences and kennel runs

6 foot cedar or chain link with buried wire dig guards along the bottom, puppy pickets on iron fences, and latches a nose cannot open. Kennel runs get a gravel or concrete floor and a gate wide enough for a wheelbarrow.

Pergolas and shade structures

Cedar and steel pergolas over a patio or along the fence line, with shade cloth or louvered tops for the afternoon sun. Posts are anchored for wind, and the crew that builds your fence stains the pergola with it so the two match.

Repair and finish

Fence repair and staining

Wind does more damage to Lubbock fences than anything else, and sun does the rest. These are the calls we take most.

Wind and storm fence repair

The phone rings the morning after every big blow. Most of what we see is the same: wood posts snapped flush with the dirt, panels flat in the alley, the rest of the run leaning. We brace what can be saved, swap the broken posts for steel, rehang the panels, and photograph everything with an itemized quote for the insurance claim. Once more than a third of the line is gone, a rebuild usually costs less than patching.

Post replacement: wood to steel

Rotted 4x4 posts cut out at the base and replaced with galvanized steel set in concrete, with brackets fastened to the existing rails. Most older fences in town need this before anything else, and the pickets can often stay up while we work.

Gate repair and sag fixes

Dragging, sagging wood gates rebuilt on a welded steel frame with heavy hinges, new latches and a drop rod, and gate posts reset in fresh concrete when they have moved.

Fence staining and sealing

Oil-based semi-transparent stain, sprayed and back-brushed into the grain once new cedar has weathered a few weeks. Under High Plains sun most fences need it every two to three years; grey fences get a power wash and brightener first.

Fence replacement and tear-out

Old wood, chain link and posts taken down, concrete footings broken out and hauled away, and the new line built the same week, often the same day the old one comes down.

Fence permits and the Lubbock fence code

Whether a permit is needed, how tall a fence can be in the front yard against the side and back, alleys and easements, and sight lines on corner lots. We check your lot against the City of Lubbock’s current rules before we quote.

Why it stays standing

Built for West Texas wind and caliche

A solid 6 foot privacy fence is a sail. In a spring blow it takes the full push of the wind across every foot of its length, and the posts carry all of it. That is why the line is only as good as what is under the ground.

Steel, not wood, in the ground

Wood posts rot where they meet the soil and snap there in a gust. Galvanized steel posts hold their strength for decades, with heavier posts at gates and corners.

Through the caliche

The hard layer under the topsoil stops hand augers and shallow posts. We drill through it with a rock auger so the concrete footing sits in solid ground.

Let some wind through

On open lots, board-on-board, shadowbox gaps and iron panels take less push than a solid wall of pickets. Stain then keeps the cedar from drying, cupping and splitting.

TopsoilCaliche layerConcrete footingbelow the calicheCedar railsGalvanized steel post
Post depth and footing size change with height, gate weight and what the auger finds. We set them by the fence, not by a rule of thumb.

Commercial

Commercial fencing in Lubbock

Rental property and apartment fencing

Privacy fence replacement and quick repairs for property managers, by the house or across a portfolio, including student rentals near the university, with one invoice for the lot.

Ag, gin and industrial yard fencing

6 and 8 foot galvanized chain link with barbed wire, cantilever slide gates and pipe perimeter fence for equipment yards, grain and cotton facilities and shops.

Church, school and ballfield fencing

Backstops and outfield chain link, playground enclosures, parking lot perimeters and ornamental steel at the entrance, priced as one campus.

Retail, restaurant and dumpster enclosures

Cedar and steel dumpster enclosures, patio fencing, HVAC screens and bollards, with installs scheduled after hours so the business stays open.

Pricing

What a fence costs in Lubbock

Installed prices per linear foot for a typical residential job. Gates, tear-out, slopes, corners and hard caliche move the number; your written quote is the real figure.

FencePer linear foot, installed200 feet, typical
Cedar privacy on steel posts, 6 ft$30 to $45$6,000 to $9,000
Board-on-board cedar with cap and trim$40 to $60$8,000 to $12,000
Wrought iron and ornamental steel$35 to $65$7,000 to $13,000
Welded pipe ranch fence$20 to $40$4,000 to $8,000
Chain link, 4 to 6 ft$15 to $30$3,000 to $6,000
Vinyl privacy$35 to $60$7,000 to $12,000

Area estimates for planning, not a quote. Financing is available through the contractor on larger jobs; ask when we bring the quote.

How a job runs

From the first call to the last gate swing

  1. Step 1

    Call or send photos

    Tell us the length, the style and what is there now. A few phone photos help us bring the right samples.

  2. Step 2

    Measure and style walk

    We walk the line, mark gates and corners, and talk through cedar, iron, pipe or chain link on site.

  3. Step 3

    Written quote in 24 hours

    An itemized quote by the foot, with gates, tear-out and stain listed separately so nothing is a surprise.

  4. Step 4

    Lot and code check

    We check the City's current rules and any HOA guidelines, and call in the utility locate before digging.

  5. Step 5

    Posts set and cured

    Holes drilled through the caliche, steel posts set in concrete and left to cure before the rails go on.

  6. Step 6

    Rails, pickets and gates

    Most backyards are framed, picketed and gated in one to two days, with the yard cleaned up each night.

  7. Step 7

    Walkthrough

    We walk the finished line with you, swing every gate and adjust latches before we call it done.

  8. Step 8

    Stain when the cedar is ready

    After a few weeks of weathering we come back to stain and seal, if you chose it.

Materials

Materials, hardware and finishes

  • Western red and Japanese cedar pickets, rails and caps
  • 2 3/8 inch galvanized steel line posts; heavier posts at gates and corners
  • Square-tube steel and powder-coated ornamental panels
  • New and drill-stem pipe, cable and sucker rod for ranch fence
  • 9 and 11 gauge galvanized and vinyl-coated chain link
  • Stainless and hot-dip galvanized fasteners and hinges
  • Oil-based semi-transparent stains and sealers

Brands and warranties are named on your written quote.

Before you build

Permits and the Lubbock fence code

The City of Lubbock sets how tall a fence can be in a front yard compared with the side and back, when a building permit is needed, and how close a fence can come to an alley, an easement or the corner of two streets. Neighborhood associations can add their own style and stain rules on top. We check your lot against the City's current rules, and any HOA guidelines you share, before we quote, so the fence goes up once.

Fence styles

Fences around Lubbock

Typical jobs, so you can picture the size and the timeline.

Backyard cedar privacy

About 180 feet of 6 foot cedar on steel posts with one walk gate, replacing an old wood-post fence.

Typical: 1 to 2 days · about $5,400 to $8,100

Corner lot board-on-board

About 220 feet of board-on-board with cap and trim, stained after four to six weeks, with a double drive gate.

Typical: 2 to 3 days · about $8,800 to $13,200

Acreage pipe fence

About 600 feet of welded pipe with cable rails and a 16 foot entry gate on a few acres outside town.

Typical: about a week · about $12,000 to $24,000

Service area

Serving Lubbock and the South Plains

From central Lubbock to the new subdivisions on the south side and out to acreage homes in the county, our crew builds and repairs fences across the area.

  • Lubbock
  • Wolfforth
  • Shallowater
  • Slaton
  • Idalou
  • Ransom Canyon
  • Levelland
  • Abernathy
  • New Deal
  • Lubbock County

Questions

Fence FAQ

How much does a 200 foot privacy fence cost in Lubbock?

A 6 foot cedar privacy fence on steel posts usually runs about $6,000 to $9,000 for 200 feet installed, before gates and tear-out.

Why do Lubbock fences use steel posts?

Wood posts rot at the ground line and snap there in high wind. Galvanized steel posts last far longer and hold the line straight.

How deep do you set posts through caliche?

Deep enough to put the concrete footing in solid ground below the caliche. Depth depends on fence height, gate weight and what the auger finds.

Do I need a permit for a fence in Lubbock?

It depends on the height and where the fence sits on the lot. We check the City of Lubbock's current rules for your address before we quote.

How tall can a backyard fence be?

The City sets different limits for front yards and for side and rear yards. We confirm the current limit for your lot so the fence passes.

Can you replace rotted wood posts without a new fence?

Yes. We cut out the old posts, set galvanized steel in concrete and bracket the existing rails, often with the pickets still up.

How soon after a windstorm can you come out?

Storm repairs go to the front of the schedule. Call with photos and we will brace what can be saved first.

When should new cedar be stained?

After it has weathered for a few weeks and dried out, so the stain soaks into the grain instead of sitting on top.

How often should a fence be restained?

Every two to three years under West Texas sun, sooner on fences that face south or west.

Is vinyl a good choice in Lubbock wind?

It can be with steel-reinforced posts. On very open, windward lots we usually suggest board-on-board cedar or iron instead.

Board-on-board or side-by-side pickets?

Side-by-side costs less. Board-on-board overlaps the pickets, so no gaps open as the cedar shrinks and both sides look finished.

Can you build a pergola to match the fence?

Yes. The same crew builds it in cedar or steel and stains it with the fence so the colors match.

Do you build pipe fence for horses?

Yes, welded pipe with pipe, cable or sucker-rod rails, plus wide entry gates for trailers and equipment.

Do you offer financing?

Financing is available through the contractor for larger jobs. Ask when we bring the quote.

Which towns do you serve?

Lubbock, Wolfforth, Shallowater, Slaton, Idalou, Ransom Canyon, Levelland, Abernathy, New Deal and the rest of Lubbock County.

Free quote

Call or request a quote

Send the rough length, the fence you want and a photo if you have one. We measure, check the lot and send a written quote within 24 hours.

Call or text; the written quote follows the measure.

Talk to a fence contractor

Request a written quote

The measure is free; the written quote follows within a day of it.

Call (806) 555-0100nowFree quote